10.100.1.1 router login

Confirm the computer is joined to the network the router serves, not a guest SSID, a neighbouring network or a mobile hotspot. Guest networks are commonly isolated from the management interface by design. Then test reachability with ping 10.100.1.1 before blaming the browser: if the ping fails, the problem is the network path, not the web page.

On Windows run ipconfig /all in Command Prompt and read the Default Gateway line for your active adapter. On Linux run ip route and look at the address after "default via". On macOS open System Settings, Network, select the active connection, then Details and TCP/IP, and read the Router field. If it shows a different address, browse to that one instead.

Corporate VPN clients frequently push a route for the whole of 10.0.0.0/8, so traffic to 10.100.1.1 is sent down the tunnel rather than to the router in front of you. The symptom is a page that times out only while the VPN is connected. Disconnect the VPN, or check its split-tunnel configuration, then retry the address.

Type http://10.100.1.1 in full. Left to itself a browser may treat a bare address as a search term or force an HTTPS attempt the device cannot answer. Some units listen on 8080 or 8443 instead, reachable as http://10.100.1.1:8080. Certificate warnings are normal on private addresses, because no public authority issues certificates for RFC 1918 space.

There is no www prefix and no domain suffix; 10.100.1.1.com or www.10.100.1.1 will not resolve. Watch for near misses such as 10.100.11.1, 10.100.1.11, 10.10.0.1 and 10.1.100.1, all of them valid private addresses that may belong to something else entirely on a network using 10.0.0.0/8. Clear the address bar completely before retyping.

Check caps lock and any autofilled entry left over from a different router. Then compare what you are typing against the label on the device itself, since many provider-supplied units carry a per-device password rather than a shared one. Repeated failures can trigger a lockout of several minutes on some firmware, so pause rather than retrying in quick succession.

No. 10.0.0.0/8 is private space under RFC 1918, and providers do not route it across the public internet. Traffic sent to 10.100.1.1 stays inside whatever local network you are attached to. That is also why the address only means something once you are connected to the network in question, whether by cable, Wi-Fi or VPN.

Nobody, and nowhere in particular. Addresses in 10.0.0.0/8 are unallocated private space that anyone may use inside their own network, so there is no registrant, no operator and no geographic location attached to this address. Any lookup service that claims a country, city or company for it is reporting something it cannot know.

Vodafone Station series routers are documented as shipping with this address as their gateway. Beyond that, any router, firewall or virtual appliance can be configured onto 10.100.1.1 by hand, which is common in corporate networks, ISP-managed equipment and container platforms that carve small subnets out of the /8. The address alone does not identify the make of the device.

There is no default that belongs to the address itself, and none is recorded here. The credentials depend entirely on the device answering on it. Check the label on the router, the quick-start card, the manual for the exact model, or the documentation from the provider that supplied the equipment. Many recent units carry a password unique to that individual device.

192.168.0.0/16 is small and heavily used by home equipment, so networks that need many subnets, or that must avoid clashing with the home networks their remote workers dial in from, tend to allocate out of 10.0.0.0/8 instead. Picking something like 10.100.1.0/24 keeps a distinctive range that is unlikely to collide over a VPN.

The subnet holds 254 usable addresses, 10.100.1.1 through 10.100.1.254. 10.100.1.0 identifies the network and 10.100.1.255 is the broadcast address, so neither can be assigned to a host. The gateway takes one of the usable addresses, commonly the first, leaving 253 for clients unless part of the range is reserved for static assignments.

On most routers the LAN IP address is editable in the network or LAN settings. If you change it, the DHCP pool has to sit inside the new subnet, existing clients need to renew their leases before they can reach the router again, and any port forwarding rules or bookmarks pointing at 10.100.1.1 will need updating. Provider-managed devices may block the change.