10.200.200.2 router login
To open the admin panel, type 10.200.200.2 into your browser's address bar. If the page does not load, this is probably not the gateway address on your network — see the checks below.
10.200.200.2 router passwords
Where to find them:
- The label on the underside or back of the router — most manufacturers print the default admin username, password and Wi-Fi key there.
- The quick-start card or manual that came in the box.
- Your ISP's account portal, if the device was supplied by them — many set a unique password per line rather than a shared default.
No credential pair is documented for 10.200.200.2. Addresses in deliberately chosen ranges like this one are nearly always configured by an administrator, which makes any published default doubly unlikely to be correct — the factory password has usually been replaced during setup.
If the device is yours and still on its shipping configuration, the label on the unit is where manufacturers commonly print the default account and password. If it belongs to an employer, a client site or a VPN provider, the credentials are held by whoever built the tunnel, and requesting them is the only reliable route.
How to log in to your router
Type 10.200.200.2 into your browser's address bar and press Enter. Type it by hand rather than accepting an autocomplete suggestion, which often fills in a different address you visited before.
If the browser reports that it cannot reach 10.200.200.2, this is not the gateway address on your network. On Windows run ipconfig /all and read the Default Gateway line; on macOS open System Settings, Network, Details, TCP/IP; on Linux run ip route and read the address after "default via".
If the login page loads but rejects your credentials, and you have never changed them, use the defaults printed on the device's label. If they have been changed and nobody knows the new password, a factory reset is the only way back in.
If you do not know the password
Because addresses like 10.200.200.2 often mark one end of a tunnel or a hand-configured link, losing access here is usually a configuration problem rather than a lost-password problem. Check that the tunnel is up, that routes for this subnet exist on your side, and that no firewall rule is silently dropping management traffic.
A factory reset is a heavy remedy in that context. It erases addressing, routing, tunnel definitions, pre-shared keys and certificates, which will break the link for every other participant, not just for you. With no vendor documented for this address, follow the reset method described for your own equipment.
10.200.200.2 comes from 10.0.0.0/8, the broadest private range in RFC 1918. Its 255.0.0.0 mask spans 16,777,216 addresses, enough that organisations subnet it aggressively for corporate and campus use, ISP-managed CPE, carrier equipment, VPN pools and container networking. The address carries no geography and no registrant; it exists independently on any number of unrelated networks.
Its subnet is 10.200.200.0/24, running from 10.200.200.1 to 10.200.200.254 with 10.200.200.255 as broadcast. Only four other addresses in this subnet have documented entries, which fits its character: repeated high octets like 200.200 are usually a deliberate administrative choice, picked precisely because they are unlikely to collide with the default numbering on either side of a tunnel or a merged network.
Host 2 is the second usable address. It is not the conventional gateway position, but low numbers such as this are often assigned by hand rather than by DHCP — the far end of a point-to-point link, a secondary router, a management interface or a fixed service host. Someone looking this address up has typically seen it in a VPN client's routing table, a tunnel configuration or a firewall rule and is trying to work out which side of the link it belongs to.
Whois information for 10.0.0.0/8
# ARIN WHOIS data and services are subject to the Terms of Use
# available at: https://www.arin.net/resources/registry/whois/tou/
#
# If you see inaccuracies in the results, please report at
# https://www.arin.net/resources/registry/whois/inaccuracy_reporting/
#
# Copyright 1997-2024, American Registry for Internet Numbers, Ltd.
#
NetRange: 10.0.0.0 - 10.255.255.255
CIDR: 10.0.0.0/8
NetName: PRIVATE-ADDRESS-ABLK-RFC1918-IANA-RESERVED
NetHandle: NET-10-0-0-0-1
Parent: ()
NetType: IANA Special Use
OriginAS:
Organization: Internet Assigned Numbers Authority (IANA)
RegDate: 1995-06-23
Updated: 2013-08-30
Comment: These addresses are in use by many millions of independently operated networks, which might be as small as a single computer connected to a home gateway, and are automatically configured in hundreds of millions of devices. They are only intended for use within a private context and traffic that needs to cross the Internet will need to use a different, unique address.
Comment:
Comment: These addresses can be used by anyone without any need to coordinate with IANA or an Internet registry. The traffic from these addresses does not come from ICANN or IANA. We are not the source of activity you may see on logs or in e-mail records. Please refer to http://www.iana.org/abuse/answers
Comment:
Comment: These addresses were assigned by the IETF, the organization that develops Internet protocols, in the Best Current Practice document, RFC 1918 which can be found at:
Comment: http://datatracker.ietf.org/doc/rfc1918
Ref: https://rdap.arin.net/registry/ip/10.0.0.0
OrgName: Internet Assigned Numbers Authority
OrgId: IANA
Address: 12025 Waterfront Drive
Address: Suite 300
City: Los Angeles
StateProv: CA
PostalCode: 90094
Country: US
RegDate:
Updated: 2012-08-31
Ref: https://rdap.arin.net/registry/entity/IANA
OrgAbuseHandle: IANA-IP-ARIN
OrgAbuseName: ICANN
OrgAbusePhone: +1-310-301-5820
OrgAbuseEmail: abuse@iana.org
OrgAbuseRef: https://rdap.arin.net/registry/entity/IANA-IP-ARIN
OrgTechHandle: IANA-IP-ARIN
OrgTechName: ICANN
OrgTechPhone: +1-310-301-5820
OrgTechEmail: abuse@iana.org
OrgTechRef: https://rdap.arin.net/registry/entity/IANA-IP-ARIN
Other documented addresses in 10.200.200.0/24
The 10.200.200.0/24 subnet runs from 10.200.200.1 to 10.200.200.254, with 10.200.200.255 reserved as the broadcast address. These are the addresses in it we hold router login details for.
All addresses we cover here
5 addresses in this subnet have a page; the most looked-up are listed here.