10.0.0.62 router login
To open the admin panel, type 10.0.0.62 into your browser's address bar. If the page does not load, this is probably not the gateway address on your network — see the checks below.
10.0.0.62 router passwords
Where to find them:
- The label on the underside or back of the router — most manufacturers print the default admin username, password and Wi-Fi key there.
- The quick-start card or manual that came in the box.
- Your ISP's account portal, if the device was supplied by them — many set a unique password per line rather than a shared default.
No default login is recorded for 10.0.0.62, and inventing one would be worse than useless in a range this widely reused. In corporate and ISP-managed deployments, factory credentials are frequently replaced during provisioning anyway, so the sticker on the chassis may already be out of date. Start there regardless, then consult the model's manual. If the equipment was installed by an employer, a managed service provider or an internet provider, the working credentials are held by whoever provisioned it, and asking them is the correct route.
How to log in to your router
Type 10.0.0.62 into your browser's address bar and press Enter. Type it by hand rather than accepting an autocomplete suggestion, which often fills in a different address you visited before.
If the browser reports that it cannot reach 10.0.0.62, this is not the gateway address on your network. On Windows run ipconfig /all and read the Default Gateway line; on macOS open System Settings, Network, Details, TCP/IP; on Linux run ip route and read the address after "default via".
If the login page loads but rejects your credentials, and you have never changed them, use the defaults printed on the device's label. If they have been changed and nobody knows the new password, a factory reset is the only way back in.
If you do not know the password
A factory reset on managed or provider-supplied equipment carries a heavier price than it does at home. Alongside the expected losses of wireless keys, firewall rules and address reservations, you can also strip out configuration pushed down by a provisioning system, VLAN and routing setup, and remote management access, potentially leaving the device unreachable until someone re-provisions it. If the hardware belongs to an employer or an ISP, contact them before pressing anything. Where a reset is authorised, the standard method is a recessed button held for a sustained interval with the unit powered on.
10.0.0.62 lies in 10.0.0.0/8, the largest of the three RFC 1918 private ranges, holding 16,777,216 addresses under the mask 255.0.0.0. That scale is why the block dominates corporate and campus networks, ISP-managed customer equipment, carrier-grade gear, VPN address pools and container and orchestration networks, all of which subnet it far below its nominal /8. A /8 boundary is almost never used as-is; what an operator actually deploys is a much smaller slice.
One such slice is 10.0.0.0/24, the subnet containing this address, with usable hosts from 10.0.0.1 to 10.0.0.254 and a broadcast address of 10.0.0.255. Host 62 sits in the middle third of that range. It is not one of the low positions an administrator would normally reserve for a gateway or a router interface, and it falls comfortably inside the span that DHCP servers typically hand out.
People looking up this number are usually working out what device on their own network answers to it, whether from a connected-clients list, a lease table or the output of a network scan.
Whois information for 10.0.0.0/8
# ARIN WHOIS data and services are subject to the Terms of Use
# available at: https://www.arin.net/resources/registry/whois/tou/
#
# If you see inaccuracies in the results, please report at
# https://www.arin.net/resources/registry/whois/inaccuracy_reporting/
#
# Copyright 1997-2024, American Registry for Internet Numbers, Ltd.
#
NetRange: 10.0.0.0 - 10.255.255.255
CIDR: 10.0.0.0/8
NetName: PRIVATE-ADDRESS-ABLK-RFC1918-IANA-RESERVED
NetHandle: NET-10-0-0-0-1
Parent: ()
NetType: IANA Special Use
OriginAS:
Organization: Internet Assigned Numbers Authority (IANA)
RegDate: 1995-06-23
Updated: 2013-08-30
Comment: These addresses are in use by many millions of independently operated networks, which might be as small as a single computer connected to a home gateway, and are automatically configured in hundreds of millions of devices. They are only intended for use within a private context and traffic that needs to cross the Internet will need to use a different, unique address.
Comment:
Comment: These addresses can be used by anyone without any need to coordinate with IANA or an Internet registry. The traffic from these addresses does not come from ICANN or IANA. We are not the source of activity you may see on logs or in e-mail records. Please refer to http://www.iana.org/abuse/answers
Comment:
Comment: These addresses were assigned by the IETF, the organization that develops Internet protocols, in the Best Current Practice document, RFC 1918 which can be found at:
Comment: http://datatracker.ietf.org/doc/rfc1918
Ref: https://rdap.arin.net/registry/ip/10.0.0.0
OrgName: Internet Assigned Numbers Authority
OrgId: IANA
Address: 12025 Waterfront Drive
Address: Suite 300
City: Los Angeles
StateProv: CA
PostalCode: 90094
Country: US
RegDate:
Updated: 2012-08-31
Ref: https://rdap.arin.net/registry/entity/IANA
OrgAbuseHandle: IANA-IP-ARIN
OrgAbuseName: ICANN
OrgAbusePhone: +1-310-301-5820
OrgAbuseEmail: abuse@iana.org
OrgAbuseRef: https://rdap.arin.net/registry/entity/IANA-IP-ARIN
OrgTechHandle: IANA-IP-ARIN
OrgTechName: ICANN
OrgTechPhone: +1-310-301-5820
OrgTechEmail: abuse@iana.org
OrgTechRef: https://rdap.arin.net/registry/entity/IANA-IP-ARIN
Other documented addresses in 10.0.0.0/24
The 10.0.0.0/24 subnet runs from 10.0.0.1 to 10.0.0.254, with 10.0.0.255 reserved as the broadcast address. These are the addresses in it we hold router login details for.
Most looked up in this subnet
All addresses we cover here
255 addresses in this subnet have a page; the most looked-up are listed here.